Hallo Zusammen,
ich habe nochmals ein ifconfig -a abgesetzt:
eth0 Protokoll:Ethernet Hardware Adresse 00:A0:D1:CE:0F:82
inet Adresse:192.168.2.34 Bcast:192.168.2.255 Maske:255.255.255.0
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
Kollisionen:0 Sendewarteschlangenlänge:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:233 Basisadresse:0x4800
lo Protokoll:Lokale Schleife
inet Adresse:127.0.0.1 Maske:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:24 errors:0 dropped:0 overruns:0 frame:0
TX packets:24 errors:0 dropped:0 overruns:0 carrier:0
Kollisionen:0 Sendewarteschlangenlänge:0
RX bytes:1664 (1.6 KiB) TX bytes:1664 (1.6 KiB)
Mit dem Befehl dmseg bekomme ich eine recht lange Liste.
Ohne Netzkabel sieht es wie folgt aus: (ich kopiere mal die letzten Zeilen rein)
loop: loaded (max 8 devices)
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised:
dm-devel@redhat.comLinux agpgart interface v0.101 (c) Dave Jones
eth0: link down
ACPI: Battery Slot [BAT0] (battery present)
ACPI: AC Adapter [ADP0] (off-line)
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Lid Switch [LID]
lp: driver loaded but no devices found
ppdev: user-space parallel port driver
Bluetooth: Core ver 2.10
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
usb 5-3: new high speed USB device using ehci_hcd and address 3
usb 5-3: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
scsi2 : SCSI emulation for USB Mass Storage devices
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
Vendor: USB 2.0 Model: Flash Disk Rev: 0.00
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sdb: 2015232 512-byte hdwr sectors (1032 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 00 00 00
sdb: assuming drive cache: write through
SCSI device sdb: 2015232 512-byte hdwr sectors (1032 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 00 00 00
sdb: assuming drive cache: write through
sdb: unknown partition table
sd 2:0:0:0: Attached scsi removable disk sdb
usb-storage: device scan complete
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will b e case sensitive!
Mit Netzwerkkabel dann wie folgt:
loop: loaded (max 8 devices)
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised:
dm-devel@redhat.comLinux agpgart interface v0.101 (c) Dave Jones
eth0: link down
ACPI: Battery Slot [BAT0] (battery present)
ACPI: AC Adapter [ADP0] (off-line)
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Lid Switch [LID]
lp: driver loaded but no devices found
ppdev: user-space parallel port driver
Bluetooth: Core ver 2.10
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
usb 5-3: new high speed USB device using ehci_hcd and address 3
usb 5-3: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
scsi2 : SCSI emulation for USB Mass Storage devices
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
Vendor: USB 2.0 Model: Flash Disk Rev: 0.00
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sdb: 2015232 512-byte hdwr sectors (1032 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 00 00 00
sdb: assuming drive cache: write through
SCSI device sdb: 2015232 512-byte hdwr sectors (1032 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 00 00 00
sdb: assuming drive cache: write through
sdb: unknown partition table
sd 2:0:0:0: Attached scsi removable disk sdb
usb-storage: device scan complete
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
Den restlichen Text hätte ich auch noch zur Verfügung. Hänge ich mal als Textdatei an.
Gruß und Danke Malte
- debian.txt
- ifconfig - a und dmesg
- (34.46 KiB) 132-mal heruntergeladen